How to Interface Interrupts with PIC16F877A

External Interrupt Interfacing with PIC16F877A Friendly

Tags: Working with interrupts using pic16f877a,interrupts source code using PIC16F877A, Interrupts in PIC16F877A,
Overall rating
PIC16F/18F Evaluation Board

The PIC16F/18F Evaluation board is specifically designed to help students to master the required skills in the area of embedded systems. The kit is designed in such way that all the possible features of the microcontroller will be easily used by the students. The kit supports in system programming (ISP) which is done through USB port.

Microchip’s PIC (PIC16F877A), PIC16F/18F Evaluation Kit is proposed to smooth the progress of developing and debugging of various designs encompassing of High speed 8-bit Microcontrollers.

External Interrupts

An interrupt caused by an external source such as the computer operator, external sensor or monitoring device, or another computer. Interrupts are special events that require immediate attention.

Interfacing External Interrupts

Fig. 1 shows how to interface the External Interrupt to microcontroller. Interrupts cause the processor to cease the running task to serve a special task for which the interrupt event had occurred. After the special task is over, the processor resumes performing the original task.

The processor can also serve these events by polling method. But polling is an inefficient technique as compared to interrupts. In the polling method, the processor has to continuously wait for the event signal. Thus it always remains busy using extra resources.


Fig. 1 Interfacing External Interrupts to Microcontroller

Interfacing External Interrupts with PIC16F877A

We now want to display some messages in PC when occur an external interrupt signal in PIC16F/18F Evaluation Board. The Interrupt signal is occurred by using switches. When the switch is pressed to LOW, then the external interrupt is occurred.

The Vectored Interrupt Controller (VIC) takes 32 interrupt request inputs and programmable assigns them into 3 categories, FIQ, vectored IRQ, and non-vectored IRQ.

The PIC16F/18F Evaluation board has only one External Interrupt, connected with I/O Port line (PORTB.0) as a switch.

Pin Assignment with PIC16F877A




PIC16F/18F Lines



Tactile Switch






SW3 – (INT0)



*Place a jumper between Middle and RB pins of J11 (INT0).

*Place a Jumper Between Middle and FE pin J8 to select Falling Edge.

*Connect PORTC with JP3 (LED section) via FRC cable

Outputs: Press SW3 switch and the PORTC.0(D5) LED will be toggled for every Pressing made by INT0


Circuit Diagram for Ext-Interrupt with PIC16F877A


Source Code

The Interfacing External Interrupt with PIC16F877A program is very simple and straight forward, that accessed by using switches. When the two external interrupts occurring, some messages are displayed in PC through serial port at 9600 baud rate. The C programs are written in Mplab software & Hi-Tech Compiler.

C Program to interface Ext-Interrupt using PIC16F


Title : Program to interface an external Interrupt




#include <pic.h>     // Define PIC Registers


//Select HS oscillator, Enable (PWRTE,BOREN),

//Disable (CPD,CP,WDTEN,In-circuit Debugger)

void DelayMs(unsigned int);

void main()


      OPTION_REG=0;     // Enable Internal Pull-ups and Interrupt on falling edge

      TRISB=0x01;            // Configure RB0 as I/P

      TRISC=0x00;            // Configure PORTC as O/P



      INTCON=0x90;      // Enable the Global Interrupt & External Interrupt




void interrupt rb0_int(void)


      if(INTF)                       // Wait until External Interrupt occurs


           RC0^=1;                  // Toggle PORTC Pin RC0

           INTF=0;                  // clear the External Interrupt flag

           while((PORTB & 0x01)==0);   // stay until interrupt on pin RB0 released




void DelayMs(unsigned int Ms)


      int delay_cnst;




           for(delay_cnst = 0;delay_cnst <220;delay_cnst++);






To compile the above C code you must need the Mplab software & Hi-Tech Compiler. They must be properly set up and a project with correct settings must be created in order to compile the code. To compile the above code, the C file must be added to the project.

In Mplab, you want to develop or debug the project without any hardware setup. You must compile the code for generating HEX file. In debugging Mode, you want to check the port output without PIC16F/18F Evaluation Board.

The PICKIT2 software is used to download the hex file into your microcontroller IC PIC16F/18F through USB port.

Testing the External Interrupts with PIC16F877A

Give +12V power supply to PIC16F/18F Evaluation Board; the serial cable is connected between the PIC16F/18F Evaluation Board and PC. Open the Hyper Terminal screen, select which port you are using and set the default settings. Now the screen should show which external interrupt is selected.

When you pressed the interrupt key, the screen should update which interrupt is now pressed. The external Interrupts are controlled by using switches. If any data is not coming in Hyper Terminal, then you just check the serial cable is working or not. Otherwise you just check the code with debugging mode in Mplab. If you want to see more details about debugging just see the videos in below link.

General Information

Join the World's Largest Technical Community

we respect your privacy.