You have no items in your shopping cart.

Subtotal: 0.00

ARM7 LPC2148 Development Board

The ARM7 LPC2148 Development Board is specifically designed to help students to master the required skills in the area of embedded systems. The kit is designed in such way that all the possible features of the microcontroller will be easily used by the students. The kit supports in system programming (ISP) which is done through serial port.

NXP’s ARM7 (LPC2148), ARM Development Kit is proposed to smooth the progress of developing and debugging of various designs encompassing of High speed 32-bit Microcontrollers.


UART (Universal Asynchronous Receiver Transmitter) are one of the basic interfaces which provide a cost effective simple and reliable communication between one controller to another controller or between a controller and PC.

RS-232 Level Converter

Usually all the digital ICs work on TTL or CMOS voltage levels which cannot be used to communicate over RS-232 protocol. So a voltage or level converter is needed which can convert TTL to RS232 and RS232 to TTL voltage levels. The most commonly used RS-232 level converter is MAX232.

This IC includes charge pump which can generate RS232 voltage levels (-10V and +10V) from 5V power supply. It also includes two receiver and two transmitters and is capable of full-duplex UART/USART communication.

☞RS-232 communication enables point-to-point data transfer. It is commonly used in data acquisition applications, for the transfer of data between the microcontroller and a PC.

☞The voltage levels of a microcontroller and PC are not directly compatible with those of RS-232, a level transition buffer such as MAX232 be used.

Interfacing UART

Fig. 1 shows how to interface the UART to microcontroller. To communicate over UART or USART, we just need three basic signals which are namely, RXD (receive), TXD (transmit), GND (common ground). So to interface UART with LPC2148, we just need the basic signals.

Fig. 1 Interfacing UART to Microcontroller

Fig. 1 Interfacing UART to Microcontroller

Interfacing UART with LPC2148

Display a text in PC using LPC2148 Development Board through UART module. In LPC2148 Development Board contains two serial interfaces that are UART0 & UART1. Here we are using UART0. The Transmitter pins send the data into PC and the receiver pin receives the data from PC. The PC and microcontroller speed are denoted by using baud rate. When the baud rates of both PC and Microcontroller are same, then only the data transmit and receive correctly otherwise not.

Pin Assignment with LPC2148



UART DB-9 Connector


Processor Lines

Serial Port Section





             Serial Port Section










Circuit Diagram to Interface UART with LPC2148

Circuit Diagram to Interface UART with LPC2148

Source Code

The Interfacing UART with LPC2148 program is very simple and straight forward, which display a text in PC from LPC2148 Development Board through UART0. Some delay is occurring when a single data is sent to PC. C programs are written in Keil software. The baud rate of microcontroller is 9600.

C Program to display a text in PC using LPC2148


Title : Program to display a text in PC using LPC2148 through UART0


#define CR 0x0D


void init_serial (void);

int putchar (int ch);

int getchar (void);

unsigned char test;

int main(void)


char *Ptr = "*** UART0 Demo ***\n\n\rType Characters to be echoed!!\n\n\r";

VPBDIV = 0x02;

// Divide Pclk by two init_serial();



while (*Ptr)





// Echo terminal



void init_serial (void)


PINSEL0 = 0x00000005;

// Enable RxD0 and TxD0 U0LCR = 0x00000083;

//8 bits, no Parity, 1 Stop bit U0DLL = 0x000000C3;

//9600 Baud Rate @ 30MHz VPB Clock U0LCR = 0x00000003;


int putchar (int ch)


if (ch == '\n')


while (!(U0LSR & 0x20));



while (!(U0LSR & 0x20));

return (U0THR = ch);


int getchar (void)


while (!(U0LSR & 0x01));

return (U0RBR);


To compile the above C code you need the KEIL software. They must be properly set up and a project with correct settings must be created in order to compile the code. To compile the above code, the C file must be added to the project.

In Keil, you want to develop or debug the project without any hardware setup. You must compile the code for generating HEX file. In debugging Mode, you want to check the port output without LPC2148 Development Board.

The Flash Magic software is used to download the hex file into your microcontroller IC LPC2148 through UART0.

Testing the UART0 with LPC2148

Give +3.3V power supply toLPC2148 Development Board; the serial cable is connected between the LPC2148 Development Board and PC. Open the Hyper Terminal screen, select which port you are using and set the default settings. Now the screen should show some text messages.

If you not reading any text from UART0, then you just check the jumper connections & just check the serial cable is working. Otherwise you just check the code with debugging mode in Keil. If you want to see more details about debugging just see the videos in below link.

How to Create & Debug a Project in Keil.

General Information

☞For proper working use the components of exact values as shown in Circuit file. Wherever possible use new components.

☞Solder everything in a clean way. A major problem arises due to improper soldering, solder jumps and loose joints.

☞Use the exact value crystal shown in schematic.

☞More instructions are available in following articles,

User Manual ARM7-LPC2148 Development Kit

Creating & Debugging a Project in KEIL