You have no items in your shopping cart.

Subtotal: 0.00

ARM7 LPC2148 Advanced Development Board

The ARM7 LPC2148 Advanced Development Board is specifically designed to help students to master the required skills in the area of embedded systems. The kit is designed in such way that all the possible features of the microcontroller will be easily used by the students. The kit supports in system programming (ISP) which is done through serial port.

NXP’s ARM7 ( LPC2148), ARM Advanced Development Kit is proposed to smooth the progress of developing and debugging of various designs encompassing of High speed 32-bit Microcontrollers.

Buzzer

Buzzer is an electrical device, which is similar to a bell that makes a buzzing noise and is used for signaling. Typical uses of buzzers and beepers include alarm devices, timers and confirmation of user input such as a mouse click or keystroke.

Interfacing Buzzer

Fig. 1 shows how to interface the Buzzer to microcontroller. A piezoelectric element may be driven by an oscillating electronic circuit or other audio signal source, driven with a piezoelectric audio amplifier. Sounds commonly used to indicate that a button has been pressed are a click, a ring or a beep. When the input port pin from microcontroller is changed, the sound wave is changed in Buzzer.



Fig. 1 Interfacing Buzzer to Microcontroller

Fig. 1 Interfacing Buzzer to Microcontroller

 

Interfacing Buzzer with LPC2148 - ARM7 Advanced Development

A small piezoelectric buzzer on the ARM2148 Slicker Kit, by pulling pin P0.7 low, current will flow through the buzzer and a relatively sharp, single-tone frequency will be heard.

The alternative PWM feature of pin P0.7 (the PWM2 signal) can be used to modulate the buzzer to oscillate around different frequencies. Then the volume of the sound will be changed by alternating the pulse width. The buzzer can be disconnected by removing jumper JP1, and this is also the default position for this jumper since the buzzer sound can be quite annoying if always left on.

Pin Assignment with LPC2148

 

Buzzer

Buzzer

LPC2148

 

LS1

I/P

P1.22

 

 



Circuit Diagram to Interface Buzzer with LPC2148 - ARM7 Advanced Development



Circuit Diagram to Interface Buzzer with LPC2148 - ARM7 Advanced Development

Source Code

The Interfacing Buzzer with LPC2148 program is very simple and straight forward. We now want to generate a sound in LPC2138 slicker Board by using a buzzer. The C programs are developed in Keil software.

C Program to generate sound in LPC2148 using Buzzer

#include 

#include 

#define BUZZ 22 void Delay(void);

void Wait(void);

void main()

{

PINSEL2 = 0x00;

//Configure Port1.22 as GPIO IODIR1 = 1 << BUZZ;

//Configure Port1.22 as O/P pin while(1)

{

IOSET0 = 1 << BUZZ;

Delay(); IOCLR0 = 1 << BUZZ; Delay();

}

}

void Delay()

{

unsigned int i,j;

for(i=0;i<1000;i++)

for(j=0;j<700;j++);

}

To compile the above C code you need the KEIL software. They must be properly set up and a project with correct settings must be created in order to compile the code. To compile the above code, the C file must be added to the project.

In KEIL, you want to develop or debug the project without any hardware setup. You must compile the code for generating HEX file. In debugging Mode, you want to check the port output without LPC2148 Slicker Board.

The Flash Magic software is used to download the hex file into your microcontroller IC LPC2148 through UART0.

Testing the Buzzer with LPC2148

Give +3.3V power supply to LPC2148 Slicker Board; the Buzzer is connected with LPC2148 Slicker Board. When the program is downloading into LPC2148 in Advanced Development, the Buzzer output is working that the Buzzer is creating some sound.

If you not getting any sound from Buzzer, then you just check the jumper connections & check the Buzzer is working or not. Otherwise you just check it with debugging mode in KEIL. If you want to see more details about debugging just see the videos in below link.

How to Create and Debug a Project in Keil

General Information

☞For proper working use the components of exact values as shown in Circuit file. Wherever possible use new components.

☞Solder everything in a clean way. A major problem arises due to improper soldering, solder jumps and loose joints.

☞Use the exact value crystal shown in schematic.

☞More instructions are available in following articles,

User Manual for NXP LPC213X Advanced Development Board

Creating & Debugging a Project in KEIL