DC To DC Converter With Soft Switching Capability

8,500.00

To increase the conversion efficiency and soft switching by using dc to dc converter with soft switching capability

3 in stock

SKU: DC To DC Converter With Soft Switching Capability Category:

Description

ABSTRACT

A new method for deriving isolated DC-DC converter with single-stage power conversion is proposed in this project. The semiconductors, conduction losses and switching losses are reduced significantly by integrating the interleaved DC converters into the full-bridge diode-rectifier. Various high-frequency bridgeless DC rectifiers are harvested based on different types of interleaved DC converters, including conventional DC converter and high step-up DC converters with soft switching.

DEMO VIDEO

EXISTING SYSTEM

The non-isolated DC cell in the non-isolated two-switch DC-DC converter with an isolated DC cell, the structure of the IBB converters presented. Although wide voltage gain range with flexible control can be achieved, it should be noted that the conversion efficiency will be hurt by the cascaded two-stage conversion architecture due to the additional conduction and switching losses.

PROPOSED SYSTEM

Based on the proposed dc to dc converter with soft switching capability can be derived by employing the input stage of an isolated DC converter as the primary-side circuit of the IBB converters. The primary-side circuit can be full-bridge, half-bridge or three-level half-bridge, etc., as shown. Since the focus of this paper is the DC rectifiers, only the IBB converter topologies with full-bridge input stage are shown. Obviously, the input stage of the IBB converter is a DC-cell, and the two cells are linked by a high-frequency inductor and transformer. This structure is similar to the non-isolated two-switch DC-DC converter.

BLOCK DIAGRAM

DC_TO_DC_CONVERTER_WITH_SOFT_SWITCHING_CAPABILITY

BLOCK DIAGRAM EXPLANATION

The input supply is fed to the isolated DC-DC converter. Present day fast converters operate at much higher switching frequencies chiefly to reduce weight and size of the filter components. As a consequence, switching losses now tend to predominate, causing the junction temperatures to rise. Special techniques are employed to obtain clean turn-on and turn-off of the devices. And the converter operates depends on load. The converter is control by driver circuit and operates by using PIC controller.

HARDWARE REQUIREMENTS

  • PIC Controller
  • Driver Board

SOFTWARE REQUIREMENTS

  • Matlab/ Simulink

ADVANTAGES

  • The voltage stresses of the semiconductor in the DC-rectifier are reduced significantly due to the voltage multiplier. Hence low voltage rated devices with better conduction and switching performance can be used to improve efficiency.
  • Soft switching within the whole operating range have been achieved for all of the active switched and diodes respectively by adopting the optimized phase shift control.

RESULT

DC_TO_DC_CONVERTER_WITH_SOFT_SWITCHING_CAPABILITY

REFERENCE

[1] G. Di Capua, S.A. Shirasavar, M.A. Hallworth, N. Femia, “An enhanced model for small-signal analysis of the phase-shifted full-bridge converter,” IEEE Trans. Power Electronics, vol. 30, no. 3, pp. 1567-1576, Mar. 2015.

[2] Z. Guo, D. Sha, X. Liao, “Input-series-output-parallel phase-shift full-bridge derived DC-DC converters with auxiliary LC networks to achieve wide zero-voltage switching range,” IEEE Trans. Power Electronics, vol. 29, no. 10, pp. 508-513, Oct. 2014.

[3] H. Wu, Y. Xing, “Families of forward converters suitable for wide input voltage range applications,” IEEE Trans. Power Electronics, vol. 29, no.11, pp. 6006-6017, Nov. 2014.

[4] Y. Wang, W. Liu, H. Ma, L. Chen, “Resonance analysis and soft-switching design of isolated DC converter with coupled inductors for vehicle inverter application,” IEEE Trans. Power Electronics, vol. 30, no. 3, pp. 1383-1392, Mar. 2015.

[5] F. Evran, M.T.  Aydemir, “Isolated High Step-Up DC-DC Converter with Low Voltage Stress,” IEEE Trans. Power Electronics, vol. 29, no. 7, pp.3591-3603, July. 2014.

For more Power Electronics Projects Click Here

Additional information

Weight2.000000 kg

Reviews

There are no reviews yet.

Be the first to review “DC To DC Converter With Soft Switching Capability”

Your email address will not be published. Required fields are marked *

two × 2 =

This site uses Akismet to reduce spam. Learn how your comment data is processed.